manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 64

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring a Wireless Network with Remote RMM-1400: Getting Started

8-2

Getting Started

This section discusses the following topics:

Wireless Network Overview

Required Components

Initial Setup

Wireless Network Overview

Remote RMM-1400 models can be equipped with 

EvDO

 or 

UMTS

 modules. These 

modules allow users to locate Remote RMM-1400s in areas that do not have 
traditional WAN connectivity. Additionally, Remote RMM-1400s located at cell sites do 
not require a dedicated T1/E1 channel for management. Full T1/E1 bandwidth is 
available for wireless customers, and management data can be carried over the 
customer network.

A wireless Remote RMM-1400 should appear as if it is a wired extension of the 
management network. The goal is to provide two-way, reliable connections with no 
restrictions on protocols over the network.

The wireless Remote RMM-1400 communicates with the service provider’s 
management network by delivering alarms to it. The management network tries to 
establish connections to Remote RMM-1400 or to network elements connected to the 
Remote RMM-1400.

Required Components

When operating in a wireless network, Remote RMM-1400 works in conjunction with 
the following Kentrox

 

products:

Connect SCS

Connect SCS acts as the VPN server for Remote RMM-1400. For more information 
about Connect SCS, refer to the 

Connect SCS Configuration Guide

.

Director SCD

Director SCD manages VPN clients and servers. It uses Director models and 
protocols to identify NEs as VPN clients or servers and manages associations 
between the clients and servers. Additionally, Director SCD manages client and 
server tokens.

Note:

A token is created by the SCD for each VPN client or server. The token must 
be installed on the client or server before it can connect to the VPN. The token 
is contained in a configuration bundle with a patch file for configuring the VPN.

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands