manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 61

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Static Routes: Adding the Default Static Route to the IP Routing Table

7-3

Adding the Default Static Route to the IP Routing Table

To add the default static route to the IP routing table:

1. At the main prompt, add the default static route with gateway address 

10.40.0.1

: 

config ip route default 10.40.0.1

2. (optional) Verify that the default static route has been added properly:

show ip route

The command response appears similar to the following:

3. Save the configuration.

In this scenario, you will add a 

default static route

 to the 

IP routing table

.

(Dub)>show ip route
Destination         Gateway          Interface                       Flags
0.0.0.0/0           10.40.0.1        bridge switch                   Up
10.40.0.0/16        0.0.0.0          bridge switch 

Up

127.0.0.0/8         0.0.0.0          *                               Up Reject
127.0.0.1/32        0.0.0.0          lo                              Up Host
128.14.0.0/16       10.40.2.18       bridge switch

Up

(Dub)>

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands