manualshive.com logo in svg

Kentrox RMM-1400, Configuration Manual

Share
Download
Kentrox RMM-1400 Configuration Manual Download Page 93

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Event Correlations: Correlation Expression Components

11-5

Example Expressions

The examples below show various forms of Terms in nested expressions.

all input 1/1-4 open and ( analog 1/1 loss-of-signal or analog 

1/1 low )

not ( any 3 analog 1/1-4 in-band and correlation myCorrelation 

false )

all input 1/1,3,5,7 open and correlation myCorrelation true

all input 1,2/1-4 open

Configuring a Time Period (Optional)

You can optionally configure a time period (duration) during which a correlation 
expression must remain in a true or false state before the correlation itself changes 
state to match the expression. 

For example, you may want to configure a scenario where an alarm is generated 
when a door is open for an extended period of time rather than a brief open/close 
situation.

Summary of Contents for RMM-1400























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands