Kentrox RMM-1400 Configuration Manual Download Page 106

Page: 106 / 246

Remote RMM-1400 Version 2.0x Configuration Guide

Configuring Alarm Entries in the Central Alarm Table: Configuring an Alarm Entry for a Serial Connection
Failure

12-10

Configuring an Alarm Entry for a Serial Connection Failure

To configure an alarm entry for a serial connection failure:

1. At the main prompt, configure description

Serial connection failure

config alarm-entry SerConnFail description Serial connection

failure

2. Enable SNMP trap alarm protocol support:

config alarm-entry SerConnFail trap enable

3. Configure an event for alarm entry

SerConnFail

with the following settings:



Event originator

serial 3



Event trigger

conn-failed



Event severity level

major



Alarm event message

The serial connection has failed

config alarm-entry SerConnFail event serial 3 conn-failed major

The serial connection has failed

In this scenario, you will:



Configure an alarm entry description



Configure SNMP alarm protocol support



Configure an alarm action that signals that a serial connection failure has
occurred.

Important:

This scenario does not show how to configure the serial port that is
associated with the alarm entry. For information on configuring serial
ports, refer to command

config controller serial

in the

Remote

RMM-1400 Command Reference Guide

Summary of Contents for RMM-1400






















































































































































































































































Search results

Summary of Contents for RMM-1400

Reviews:

Related manuals for RMM-1400

Brands by name

Popular brands

Kentrox RMM-1400, Configuration Manual

Search results

Summary of Contents for RMM-1400

Reviews:

Related manuals for RMM-1400

Brands by name

Popular brands