GE Voluson 730Pro Basic User Manual Download Page 474

Page: 474 / 480

Technical Data / Information

23.11 Volume Scan Module

Vol. scan size:

max. 64 MB

The required memory space depends on scan parameters (VOL-box

size and quality (low , mid1 , mid2 , high1 , high2).

typ.:

1-5 MB

Lines/2D-image:

max. 1024 (typ. 80 to 350)

2D-images/volume:

max. 1024 (typ. 50 to 250)

VOL-Frames/sec.:

max. 16 (typ: 3-5)

The frame rate depends on scan parameters (VOL-Box size, quality and probe.

Display of sectional plane images:

synchronous with control setting, arbitrary movement in volume,

monitored position in volume.

Rotation:

360°, 0.5° increments (X-, Y- and Z-axis)

Magnification:

adjustable from 0.25 to a factor of 4.00

3D-Rendering: Calculation and display of rendered gray scale images:

surface mode, maximum mode, minimum mode;

calculation time depending on rendering box size

Calculation and display of rendered color-images:

3D PD Mode: surface mode, max. intensity mode

3D CFM mode: display of flow direction ,surface mode, maximum

Display Modes:

3-section Mode

A triplet of 3 sectional planes normal to each other is displayed.

Full

size

image

Display of 1 single full-screen image.

Niche

image

Display of the sectional plane triplets within the (graphics) cube.

4 section Mode

Display of sectional calculated 3D images

Display graphics:

Color display of the center of rotation and the axes.

Voluson

730Pro - Operation Manual

23-8

105831 Rev. 0

Summary of Contents for Voluson 730Pro
































































































































































































































































































































































































































































































Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands

GE Voluson 730Pro, Basic User Manual

Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands