GE Voluson 730Pro Basic User Manual Download Page 98 | Manualshive

Page: 98 / 480

background image

2D Mode

5.9.1 Harmonic

Imaging

Tissue not only scatters back echoes with the nominal transmitted frequency but also with double,
threefold, fourfold and so on (harmonic) frequencies, as a result of a physical effect called
“non-linear propagation”.
Harmonic Imaging delivers better grayscale contrast compared to standard ultrasound imaging.
This technique has proved to be particularly useful for difficult-to-image patients and furthermore is
less prone to artifacts.

Switch on / off the “Harmonic Imaging” function in 2D mode.

Light illumination:

Harmonic is active.
(receiving frequency is double of the transmitted frequency)

Weak illumination:

Harmonic is useful with the selected probe, but not active

(the last adjusted transmitting frequency is active).

Not illuminated:

The use of Harmonic Imaging is impossible with the selected probe.

Use the

[

Harm. Frequ.

]

flip control to adjust the range of the frequency.

Three settings are possible: high, mid, low.

Remarks:

*

Changes are only possible in write mode.

*

The Harmonic frequency setting is displayed in 2

nd

line of the B mode Image Info area.

5.10 Optimized Tissue Imaging (OTI)

The function OTI

TM

allows the examiner to “fine tune”

the system for scanning different types of tissue.

Use the

[

OTI

]

flip switch to adjust the respective parameter.

Four positions are possible: adipose, solid, cystic or normal tissue.

Remarks:

*

Changes are only possible in write mode.

*

Setting the relevant parameter improves image quality.

Voluson

®

730Pro - Basic User Manual

5-8

105831 Rev. 0

«
...
96
97
98
99
100
...
»

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

Brand: SALUDA MEDICAL Pages: 61

Brand: Above All Pages: 4

Brand: Baker Pages: 82

Brand: Datalogic Pages: 48

Brand: PageFlip Pages: 32

Brand: Garmin Pages: 20

Brand: Nitecore Pages: 4

Brand: Pari Pages: 12

Brand: laerdal Pages: 2

Brand: laerdal Pages: 104

Brand: laerdal Pages: 33

Brand: Lafayette Pages: 2

Brand: Safety 1st Pages: 4

Brand: Safety Engineering Pages: 5

Brand: Zell Pages: 32

Brand: Uflex Pages: 16

Brand: Kärcher Pages: 20

Brand: Parker Research Corp Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands