GE Voluson 730Pro Basic User Manual Download Page 132 | Manualshive

Page: 132 / 480

background image

Spectral Doppler Mode

7.1.3.2 Format

This controls serve for selection of either one of three formats (60/40, 50/ 50 and 40/ 60) for display.

Format: large (60/40)

Format: mid (50/50)

Format: small (40/60)

7.1.3.3 Frequency

This control serves for selection of the required transmit frequency for the actual gate position.
Normally one works with the transmit frequency which is corresponding to the ultrasound element’s
properties

[

Frequency mid

]

.

With a higher transmit frequency

[

Frequency high

]

the amplitude of the Doppler spectrum is displayed

larger (advantage: better display of lower flow velocities), but the penetration depth is reduced.
With a lower transmit frequency

[

Frequency low

]

the amplitude of the Doppler spectrum is displayed

smaller (advantage: display of higher flow velocities), however the penetration depth is increased
(higher sensitivity).

The transmit frequency is displayed in the Image Info area on the screen.

low:

The transmit frequency is lower than the middle frequency of the crystal.

mid:

The transmit frequency is the middle frequency of the crystal.

high: The transmit frequency is higher than the middle frequency of the crystal.

Information of frequencies review:

Probes and Biopsy

(chapter 20)

.

Remarks:

*

Changing the PW Frequency is only possible in write mode.

Voluson

®

730Pro - Basic User Manual

7-12

105831 Rev. 0

«
...
130
131
132
133
134
...
»

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

Brand: Qingdao H.Y Pages: 6

Brand: ACS Pages: 56

Brand: MacDon Pages: 17

Brand: Olympus Pages: 50

Brand: VAHVA Pages: 19

Brand: ICS Schneider Messtechnik Pages: 124

Brand: YATEK Pages: 72

Brand: Tate Pages: 7

Brand: Tate Pages: 5

BioHarmonex BH4

Brand: Calivita Pages: 38

Brand: CAIRE Pages: 91

Brand: Datalogic Pages: 20

Brand: Datalogic Pages: 188

Brand: M-Audio Pages: 3

9NP-B7524 Series

Brand: Nautilus Pages: 2

Be strong NS 700X

Brand: Nautilus Pages: 34

Brand: Nautilus Pages: 21

Brand: PAT Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands