GE Voluson 730Pro Basic User Manual Download Page 327 | Manualshive

Page: 327 / 480

background image

Calculations and Patient Reports

Important note:

The determination of the envelope curve requires a clear and low-noise recording of the Doppler
spectrum. Otherwise the reliability of the displayed measurement results may not be ensured!

14.7.4.10.2 Manual

Trace

1. Press

the

[

Calc

]

key on the control panel.

The Cardiac calculations menu appears in the menu area.

2. Select

[

MV

]

and select

[

Manual Trace

]

.

3. The cursor appears on the Doppler spectrum. Move the cursor to the start point of the period and

press the right or left trackball

[

Set

]

key.

Note:

To readjust the traced line press the upper trackball key

[

Undo

]

repeatedly.

4. Trace to the end of the period and press the

[

Set

]

key once more.

Remarks:

•

Depending on the setting in the Measurement Setup, the envelope curve will be performed with a

continuous trace line or by setting points.

To select the Doppler Manual Trace Method review:

General Measurement Setup

(chapter 18.3.1)

14.7.4.10.3

To measure the Items One by One

To measure the Item such as Peak E, Peak A, Acc Time, Dec Time, PHT, IVRT:

1. Press

the

[

Calc

]

key on the control panel.

The Cardiac calculations menu appears in the menu area.

2. Select the appropriate item.

3. Perform the measurement by using the trackball and the right or left trackball key.

Voluson

®

730Pro - Basic User Manual

105831 Rev. 0

14-37

«
...
325
326
327
328
329
...
»

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

Brand: OfiTE Pages: 21

Brand: Earthlite Pages: 4

Brand: YATEK Pages: 78

Brand: Above All Pages: 4

Brand: Ognibene Pages: 28

Brand: Hameg Pages: 24

Brand: Vaisala Pages: 118

Brand: MacDon Pages: 46

Brand: MacDon Pages: 82

Brand: Mac Medical Pages: 2

Brand: MACDEV Pages: 8

Mentor Touch ET750

Brand: MAC TOOLS Pages: 24

Brand: MA lighting Pages: 10

Brand: Pari Pages: 11

Brand: Pari Pages: 2

Brand: Haas Pages: 5

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brand: Raymarine Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands