manualshive.com logo in svg

GE Voluson 730Pro, Basic User Manual

The GE Voluson 730Pro is a top-notch ultrasound system widely used in the medical field. Enhance your understanding and maximize its potential with the comprehensive Basic User Manual. Easily download this invaluable manual for free from manualshive.com, empowering you to make the most of your Voluson 730Pro.

Share
Download
background image

M Mode

 

 

 

 

 

6. M 

Mode 

 

 
M mode imaging provides Time and Motion echo information derived from a stationary ultrasound 
beam. M mode is used along with a 2D image. A straight line running through the 2D image, called 
the M-cursor, identifies the position of the stationary ultrasound beam from which the echo 
information is being gathered. The motion or change that occurs at this position over time is used by 
the system to generate the scrolling M mode display. 
 
M mode is primarily a cardiology mode. M mode records moving anatomical structures and produces 
subtle patterns of motion. These patterns allow you to plot temporal relationship between events in the 
cardiac cycle. Precise measurements of structures are possible with M mode. M mode also provides 
textural information that permits discriminating between normal and abnormal tissue. 
 
The M mode display contains system information, a depth scale, a time scale, a TGC curve, and a gray 
map pattern. There are three M mode display format options; review: 

Format

 

(chapter 6.3.1)

. 

 
The continuous update of the M mode display allows you immediately to recognize changes in 
anatomical position relative to the M-cursor. With this instant information you can immediately aim 
the M-line to the structures of interest by adjusting the probe.  
 
The description of M mode is subdivided in two groups. In these groups you will see how to use  
M mode and how to adjust the M mode settings. 

 

To use the M mode review: 

M Main Menu

  

(chapter 6.1)

 

To adjust M setting review: 

M Sub Menu

    

(chapter 6.3)

 

 

To use special utilities review:  

Utilities

 

 (chapter 12)  

and

  

Gray Chroma Map

  

(chapter 12.1)

  

 
 
 
 
 

6.1 

M Main Menu 

 

 

M mode key (hard key) 
 
By pressing the 

[

M

]

 control the M mode is switched on in the preparation mode, only 

the M-cursor appears on the active 2D image.  
 
 

To start and use the M mode review: 

M Operation

  

(chapter 6.2)

 

To adjust the M settings review : 

M Sub Menu  

(chapter 6.3)

 

 

 

 

This hard key is also the Gain control for the M mode ("only in write mode"). 
review: 

M Gain Control

  

(chapter 6.2.8)

 

 
 
 
 

 

 

 

  

Voluson

®

 730Pro  -  Basic User Manual 

6-2

 

 

105831   Rev. 0

 

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

ParaBody 810 Assembly Instruction Sheet preview
810
Brand: ParaBody Pages: 4
DanMedical D-MAS HyperSat 2540 Instructions For Use Manual preview
D-MAS HyperSat 2540
Brand: DanMedical Pages: 103
Bahco BH6 Service Manual preview
BH6
Brand: Bahco Pages: 9
JB-Lighting A8 Upgrade Manual preview
A8
Brand: JB-Lighting Pages: 40
EAW UX8800 Quick Start Manual preview
UX8800
Brand: EAW Pages: 2
abc 907 Instructions For Use Manual preview
907
Brand: abc Pages: 28
Taylor-Wharton XL Series Instructions Manual preview
XL Series
Brand: Taylor-Wharton Pages: 25
i-CAT FLX V Series User Manual preview
FLX V Series
Brand: i-CAT Pages: 96
MacDon A30-S Assembly Instructions Manual preview
A30-S
Brand: MacDon Pages: 46
MacDon 5020 Operator'S Manual preview
5020
Brand: MacDon Pages: 82
Mac Medical PTF1000 Preparations For Using preview
PTF1000
Brand: Mac Medical Pages: 2
MACDEV CYBORG User Manual preview
CYBORG
Brand: MACDEV Pages: 8
MAC TOOLS Mentor Touch ET750 Operating Instructions Manual preview
Mentor Touch ET750
Brand: MAC TOOLS Pages: 24
MA lighting MA Switch Repair Instructions preview
MA Switch
Brand: MA lighting Pages: 10
NanoVibronix UROSHIELD Quick Manual preview
UROSHIELD
Brand: NanoVibronix Pages: 2
NanoVibronix PainShield User Manual preview
PainShield
Brand: NanoVibronix Pages: 32
Nanoleaf Shapes Hexagons User Manual preview
Shapes Hexagons
Brand: Nanoleaf Pages: 27
Rational iCombi Pro Original Installation Manual preview
iCombi Pro
Brand: Rational Pages: 16

Brands by name

Popular brands

Load more brands