GE Voluson 730Pro Basic User Manual Download Page 365

Page: 365 / 480

Printing / Recording / Saving / Sending

16.2 VCR

Recording

The VCR comes already installed within the system.
review:

S-VHS Videorecorder Connection Scheme

(chapter 21.2.8)

By pressing the

[

VCR

]

key on the control panel the menu area as well as the status area

changes to the “VCR Remote control” menu.

The availability of the digipot-push buttons depends on the status of
the VCR.

Toggle function:

Record on / off

Pressing twice starts recording.

Pressing twice again stops recording.

[

Exit

]

changes automatically to the internal Video.

Remarks:

* By

selecting

[

Play

]

the system switches automatically to the external video source.

Always, due to quality the S-VHS source should be used. review

Peripherals

(chapter 17.3.3)

* The

[

Microphone

]

key on the control panel is only available if no Doppler signal is active.

It should only be activated during

[

Record

]

During VCR recording all other operating functions of the V730Pro are impossible.

Note:

The DIP-Switch (4) on the Video recorder changes between local and remote control.

Voluson

730Pro - Basic User Manual

105831 Rev. 0

16-5

Summary of Contents for Voluson 730Pro
































































































































































































































































































































































































































































































Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands

GE Voluson 730Pro, Basic User Manual

Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands