GE Voluson 730Pro Basic User Manual Download Page 156 | Manualshive

Page: 156 / 480

background image

CFM Mode

8.3.9 CFM

Map

This function provides selectability of the color coding for an optimization of the display of blood
flow (similar to the post-processing curves with grayscale 2D). It is useful especially with low flow
rates. It may be altered in real time or Freeze mode, respectively.

Velocity display (Display V), velocity-turbulence display (Display V-T) and velocity-power display
(Display V-Pow) each have different color pattern maps available for selection.

Selection of a CFM Map curve:

Switch the

[

C Map

]

key repeatedly to select the desired CFM Map. (1 to 8)

8.3.10 Balance

“Balance” controls the amount of Color displayed over bright echoes and helps confine Color within
the vessel walls. Raising this Balance displays Color on brighter structures. If you see Color on vessel
walls, the Balance is probably set too high. Additionally, wall motion ghosting can be suppressed with
a low Balance setting.

Rotate the

[

Balance

]

digipot and select the desired Balance.

The Balance orientation line is only visible in the color modes.
The line represents to the position of the adjusted gray value in the
gray scale.

Where the balance orientation line is on a gray step, the gray value
will be displayed (only if a color value is present, of course).
For example, if the gray value is higher than 96 while a color value is
present, the gray value will be displayed.

Remarks:

*

Changes are only possible in write mode!

Voluson® 730Pro - Basic User Manual

8-14

105831 Rev. 0

«
...
154
155
156
157
158
...
»

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

Brand: zipwake Pages: 2

Brand: zipwake Pages: 2

AJSPD850P - P2 DECK

Brand: Panasonic Pages: 73

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Brand: DBX Bushido Pages: 12

Brand: Gardner Bender Pages: 8

Brand: NARIKA Pages: 2

Brand: Öhlins Pages: 8

Brand: ?HC Pages: 2

QUICK-ALIGN Vari-Flex

Brand: Össur Pages: 36

Brand: Össur Pages: 2

Brand: Össur Pages: 8

Brand: Hammer Strength Pages: 8

Brand: IFM Pages: 105

Brand: Pasco Scientific Pages: 21

Brand: Quick Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands