GE Voluson 730Pro Basic User Manual Download Page 281 | Manualshive

Page: 281 / 480

background image

Basic Measurements

13.4 Volume

Measurements

There are four methods in which to measure the Volume of structures of different shapes.

1.  To measure the volume of an ovoid using three distances (axis).
2.  To measure the volume of the ovoid using one distance and ellipse.
3.  To measure the volume of a globe using one distance (diameter).
4.  To measure the volume in the 3D mode with the 3D MultiPlane method.

•

3 Distance Measurement

(chapter 13.4.1)

•

1 Di Ellipse Measurement

(chapter 13.4.2)

•

1 Distance Measurement

(chapter 13.4.3)

•

1 Ellipse Measurement

(chapter 13.4.4)

•

3D MultiPlane Measurement

(chapter 13.4.5)

13.4.1

3 Distance Measurement

To measure volume using three distances.

1. Select

the

[

3 Distance

]

item.

2. Move the cursor to the start of the measurement by the trackball and press the right or left

trackball key. A second cursor appears.

3. Move the second cursor to the second point of the measurement by the trackball and press the

right or left trackball key.
To re-adjust the start point, press the upper trackball key

[

Change

]

before completing the

measurement. It alternates the control from one cursor to the other.

The distance of the two points is displayed and a new cursor appears.

4. Measure the second distance as above.

5. Press

[

Freeze

]

to return to the scan mode and scan the structure transverse to the first scan.

Press

[

Freeze

]

again. A new cursor appears.

Note:

If you have scanned the second image in Dual mode previously, you can measure the third

distance within the second image.

6. Perform the measurement of the third distance in the same manner.

Remarks:

•

The Volume of the ovoid measured by three distances is displayed.

Voluson

®

730Pro - Operation Manual

105831 Rev. 0

13-7

«
...
279
280
281
282
283
...
»

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

Brand: Vahle Pages: 96

Brand: R.M. Young Pages: 10

Brand: Olympus Pages: 56

Brand: Vahle Pages: 36

Brand: Vahle Pages: 20

Brand: Vacon Pages: 102

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

Brand: Yamaha Pages: 5

Brand: ZOLL Pages: 48

Brand: Daikin Pages: 12

Brand: Napoleon Pages: 3

Brand: Daikin Pages: 52

Brand: Varimixer Pages: 28

Brand: Lumineux Pages: 2

Avisa Line XL04

Brand: FHF Pages: 2

Brand: Joerns Healthcare Pages: 106

Brand: ABB Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands