GE Voluson 730Pro Basic User Manual Download Page 462 | Manualshive

Page: 462 / 480

background image

MAN ECG preamplifier

22.

MAN ECG preamplifier

22.1 Description

•

The ECG module consists of a ECG preamplifier type MAN 6 (hardware part) and a patient
connection cable (KENDALL medizinische Erzeugnisse, Code 8/P93/07-01, Ref 3227.0701.00).

•

The connector for the patient connection cable is on the front cover of the hardware section, which
is placed in a drive-slot in the front of the ultrasound machine.

•

The ECG preamplifier type MAN6 is used for acquiring an ECG signal to be displayed with the
ultrasound image. The ECG preamplifier must not be used for ECG diagnostics. It is not intended
for use as a cardiac monitor.

•

The signal input of the ECG preamplifier is equipped with a protection against high voltages used
for defibrillation (Type BF).

•

The ECG preamplifier is connected to a connector on the rear panel of Voluson

®

730Pro.

review also: Technical Data/Information:

MAN ECG preamplifier

(chapter 23.19)

Voluson

®

730Pro - Operation Manual

22-2

105831 Rev. 0

«
...
460
461
462
463
464
...
»

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: Ace Pages: 17

Brand: ACE INSTRUMENTS Pages: 33

Brand: ACE INSTRUMENTS Pages: 2

Brand: ACE INSTRUMENTS Pages: 2

Brand: TapFlo Pages: 35

Brand: DANA Pages: 8

Brand: 2E Pages: 6

Brand: ParaBody Pages: 6

Brand: Sailmon Pages: 10

Brand: B&W Tek Pages: 12

Brand: b&o Pages: 46

Brand: Faderfox Pages: 8

Brand: Haaga Pages: 31

Varycolor MICRO 150HTI

Brand: JB-Lighting Pages: 18

Brand: H&S Pages: 42

Brand: Ideal Heating Pages: 16

So-exercise TX7

Brand: T-SoX Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands