GE Voluson 730Pro Basic User Manual Download Page 181 | Manualshive

Page: 181 / 480

background image

TD Mode

10.3.4 Baseline

The TD baseline shift can be used to prevent aliasing in one flow direction similar to the Doppler
baseline shift. Shifting the TD baseline enlarges the velocity range in one direction.
The zero line of the color bar is also shifted.

Adjust the zero line +/-

There are

8 steps in each direction.

By step 8 you see only the color wedge in one direction (maximum velocity).
The other direction is 0 (kHz, cm/s, m/s).

The maximum value and minimum value of the flow velocities are displayed at the upper and lower
edge of the color wedge.

10.3.5 Ensemble

This function controls the number of pulses for one displayed Color-Doppler line. Since several pulses
are to be evaluated for display of a result, the color display quality increases with the number of
evaluated pulses.

Switch the

[

Ensemble

]

key and select the number of pulses per color line.

max. value:

31

min. value:

7

step size:

1

Switch up or down to increase or decrease the number of pulses per color line.
With increasing TD Ensemble the frame rate decreases.

Remarks:

*

Changes are only possible in write mode!

Voluson

®

730Pro - Basic User Manual

105831 Rev. 0

10-9

«
...
179
180
181
182
183
...
»

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

Brand: Falcon Pages: 52

Brand: Yamaha Pages: 46

Lab companion SI-300

Brand: Jeio tech Pages: 69

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 4

Brand: Jct Pages: 16

Brand: H&S Pages: 42

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: KUHN Pages: 112

Brand: Federal Signal Corporation Pages: 31

TEMSTM POCKET 7.3

Brand: ASCOM Pages: 8

Brand: Chamberlain Pages: 8

Brand: LINET Pages: 25

Brand: MD SPORTS Pages: 12

Brand: SurgiVet Pages: 2

Brand: Magicfx Pages: 32

Brand: chinavasion Pages: 2

Brand: Gabocom Pages: 4

Brand: W&S Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands