GE Voluson 730Pro Basic User Manual Download Page 237

Page: 237 / 480

Volume Mode

Note:

The selected format will be present in read mode after the Real Time 4D acquisition is done.

The

[

Dual

]

screen format key is only available in Real Time 4D Rendering mode!

5. Place the Volume box over the region of interest.

The trackball has two functions: position and size of the volume box
The activated function is displayed in status area on the monitor.

Press the upper trackball key to change the function of the trackball from position
to size or vice versa.

6. Change the size of the volume box by moving the trackball.

Moving:

↑

decrease the box size in vertical direction

↓

increase the box size in vertical direction

→

increase the box size in horizontal direction

←

decrease the box size in horizontal direction

7. Set the volume sweep angle.

8. Select the Quality (low, mid1, mid2, high1, high2).

This function changes the line density against acquisition speed.

Low:

Fast speed / low scan density

This mode is selected only in case of expected movement artifacts.

A loss of volume resolution will result

Mid2:

Standard VOL scan / medium scan density

High1: Slow speed/ high scan density

9. To start 3D acquisition press the

[

Freeze

]

key, or the right trackball key

(

Start

displayed in status area of the trackball).

The volume acquisition begins, the acquired images and the corresponding
functions are displayed on the monitor.

10. Press the

[

Freeze

]

key again to stop the acquisition.

review:

After the Real Time 4D Acquisition

(chapter 11.5.4)

Voluson

730Pro - Basic User Manual

105831 Rev. 0

11-53

Summary of Contents for Voluson 730Pro
































































































































































































































































































































































































































































































Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands

GE Voluson 730Pro, Basic User Manual

Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands