GE Voluson 730Pro Basic User Manual Download Page 320

Page: 320 / 480

Calculations and Patient Reports

14.7.4.4 LV

Mass

This is used for the measurement of the Left Ventricular volume and mass.
It is correctly measured only during the diastolic phase (LV expanded).

1. Press

the

[

Calc

]

key.

The Cardiac calculations menu appears in the menu area.

2. Select

[

LV Mass

]

3. Perform the measurement of

[

Epicardial Area

]

[

Endocardial

Area

]

and

[

Epicardial Length

]

prior to the LV mass measurement.

4. When the cursor appears in the image, measure the selected item

using the trackball and the right or left trackball key

[

Set

]

5. To obtain the second, orthogonal image, press

[

Freeze

]

Scan the image and press

[

Freeze

]

again.

Note:

When using Dual 2D mode, it is not necessary to unfreeze during measurements.

14.7.4.5

LVOT- or RVOT Diameter

Note:

This 2D measurement is part of the LVOT / RVOT Doppler measurements.

To calculate LVOT- or RVOT diameter in 2D mode:

1. Press

the

[

Calc

]

key.

The cardiac calculations menu appears in the menu area.

2. Select

[

LVOT

]

[

RVOT

]

and

[

LVOT Dia

]

[

RVOT Dia

]

3. Perform the measurement by using the trackball and the right or

left trackball key

[

Set

]

Voluson

730Pro - Basic User Manual

14-30

105831 Rev. 0

Summary of Contents for Voluson 730Pro
































































































































































































































































































































































































































































































Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands

GE Voluson 730Pro, Basic User Manual

Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands