GE Voluson 730Pro Basic User Manual Download Page 116

Page: 116 / 480

M Mode

6.2 M

Operation

The M operation consists of :

Cursor Position

(chapter 6.2.1)

Activation of M Mode

(chapter

6.2.2)

Sweep Speed

(chapter 6.2.3)

Invert

(chapter 6.2.4)

Frequency

(chapter 6.2.5)

TGC Slide Controls

(chapter 6.2.6)

M Mode Depth

(chapter 6.2.7)

M Gain Control

(chapter 6.2.8)

M Cineloop

(chapter 6.2.9)

6.2.1 Cursor

Position

After pressing the

[

]

control adjust the M-cursor using the trackball in the 2D single

image.

6.2.2

Activation of M Mode

Press the right or left trackball key and 2D mode and M mode trace are active.

The screen is divided asymmetrically. In the smaller image above the 2D image
appears. In the image below the M mode trace starts running.

Three display formats are possible, review:

Format

(chapter 6.3.1)

The

[

Freeze

]

key stops the 2D image and M mode trace.

Note:

By pressing the

[

Freeze

]

key again, the M-cursor appears on the active 2D image.

Voluson

730Pro - Basic User Manual

6-4

105831 Rev. 0

Summary of Contents for Voluson 730Pro
































































































































































































































































































































































































































































































Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands

GE Voluson 730Pro, Basic User Manual

Search results

Summary of Contents for Voluson 730Pro

Reviews:

Related manuals for Voluson 730Pro

Brands by name

Popular brands