GE Voluson 730Pro Basic User Manual Download Page 155 | Manualshive

Page: 155 / 480

background image

CFM Mode

8.3.6 Baseline

The CFM baseline shift can be used to prevent aliasing in one flow direction similar to the PW
Doppler baseline shift. Shifting the CFM baseline enlarges the velocity range in one direction.
The zero line of the color bar is also shifted.

There are

8 Steps in each direction.

By step 8 you see only the color wedge in one direction (maximum velocity), the other
direction is 0 (kHz, cm/s , m/s).

Only possible in Display Mode V, V-T and V-Pow

The maximum value and minimum value of the flow velocities are displayed at the upper and lower
edge of the color wedge.

8.3.7 Ensemble

This function controls the number of pulses for one displayed Color-Doppler line. Since several pulses
are to be evaluated for display of a result, the color display quality increases with the number of
evaluated pulses.

Switch the

[

Ensemble

]

key and select the number of pulses per color line.

max. value:

31

min. value:

7

step size:

1

Switch up or down to increase or decrease the number of pulses per color line.
With increasing CFM Ensemble the frame rate decreases.

Remark:

Changes are only possible in write mode!

8.3.8 Line

Density

This function determines the line density within the CFM box. The lower the line density, the greater
the distance between lines and the size of the color pixels.

Switch the

[

Line D.

]

key and adjust the line density.

Switch up or down to increase or decrease the line density.

max. value:

9

min. value:

1

step size:

1

Remark:

Changes are only possible in write mode.

Voluson

®

730Pro - Basic User Manual

105831 Rev. 0

8-13

«
...
153
154
155
156
157
...
»

Summary of Contents for Voluson 730Pro

































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson 730Pro

Brand: Landoll Pages: 34

Brand: MacDon Pages: 2

Brand: MacDon Pages: 214

Brand: MacDon Pages: 32

Brand: Landoll Pages: 83

Brand: DBX Bushido Pages: 12

Brand: Ibiza Pages: 21

Brand: IBC Pages: 8

Brand: Ibanez Pages: 8

Brand: IAI Pages: 5

Brand: IEMCA Pages: 82

KID 80-IV Touch

Brand: IEMCA Pages: 122

Brand: Calrec Pages: 92

Brand: MAGIC FX Pages: 25

FlexDraper FD2 Series

Brand: MacDon Pages: 2

OXYGEN PRO MINI

Brand: M-Audio Pages: 56

Brand: Madsen Pages: 206

Brand: GE Pages: 644

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands