Gambro AK 98 Operator'S Manual Download Page 43

Page: 43 / 386

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Machine Description

A:41

Pick-up tube holder

The pick-up tubes not in use are kept in this holder.

BICART cartridge holder

This holder is for the BICART cartridge. The holder is
also used for CLEANCART cartridges (cleaning or
decalcification).

To attach the BICART cartridge to the Holder, see
Section 4.2.3

“Set up the dialysis machine”

page A:77.

To attach a CLEANCART cartridge to the holder, see
Section 10.3.4

“Start a heat disinfection with a

CLEANCART cartridge”

on page A:146

Blood leak detector

The blood leak detector checks for blood in the
dialysis fluid.

To open the blood leak detector cover see Section
13.3

“Clean the blood leak detector”

on page A:173.

Summary of Contents for AK 98



































































































































































































































































































































































































Search results

Summary of Contents for AK 98

Reviews:

Related manuals for AK 98

Brands by name

Popular brands

Gambro AK 98, Operator'S Manual

Search results

Summary of Contents for AK 98

Reviews:

Related manuals for AK 98

Brands by name

Popular brands