Gambro AK 98 Operator'S Manual Download Page 346 | Manualshive

Page: 346 / 386

background image

B:146

AK 98 Dialysis Machine - Attentions

HCEN12745 Revision 10.2016

Program version 2.xx

573 Low flow heat is stopped

573 Low flow heat is stopped

To continue to drain phase press Confirm.

Appears:

When the WRO 300 H cannot deliver hot water during
integrated heat disinfection program with WRO 300 H. The
low flow heat phase (where the machine receives hot water
from the WRO 300 H) will not start.

This attention can appear if you manually choose to start a
low flow heat phase but do not confirm it within 5 minutes.

Machine actions:

The low flow heat phase does not start.

Operator action:

1.

Press

Confirm

to confirm the attention. The machine

now enters drain phase.

2.

Contact an authorised technician.

Mute time:

Permanent.

«
...
344
345
346
347
348
...
»

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Related manuals for AK 98

Brand: JB Systems Pages: 7

Brand: 3B SCIENTIFIC PHYSICS Pages: 36

Brand: 3A HEALTH CARE Pages: 16

Short/cut 2000 Audio Editor

Brand: 360 Systems Pages: 4

Brand: Tate Pages: 7

Brand: Tate Pages: 5

BioHarmonex BH4

Brand: Calivita Pages: 38

Brand: CAIRE Pages: 91

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Bacharach Pages: 2

Brand: RayLight Pages: 34

GAZELLE FREESTYLE

Brand: Gazelle Pages: 10

Brand: Latham Pages: 19

Brand: Nabtesco Pages: 26

Brand: Ultrawave Pages: 30

Brand: Ultrasound Technologies Pages: 12

Brand: Vatech Pages: 137

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands