Gambro AK 98 Operator'S Manual Download Page 19 | Manualshive

Page: 19 / 386

Gambro AK 98 Operator'S Manual Download Page 19

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Before you get started

A:17

CAUTION!

Make sure that any used chemical disinfectants are stored according to
manufacturer’s recommendations.

CAUTION!

Make sure not to position the AK 98 dialysis machine in a way that it becomes
difficult to operate the mains power switch.

NOTE!

The AK 98 dialysis machine must be installed according to the Installation guide.

NOTE!

For accuracy ranges written as ”(±1 mL/min or ±1%)”, the widest range is valid.

NOTE!

It is recommended that the equipment is kept in its original packing during
transportation and storage.

NOTE!

The service manual is only available for the authorised service technician.

NOTE!

It is important that the protective earth in the installation is of high quality.

NOTE!

For the purpose of protecting the environment the AK 98 dialysis machine shall be
separately collected for dismantling and recovery. Where applicable, national
regulations shall be applied. Consult your local Baxter distributor for information.

NOTE!

To protect the machine against spillage, the infusion stand must always be correctly
mounted in the machine.

NOTE!

The WRO unit (WRO 300 or WRO 300 H) must be preset by an authorised service
technician to work correctly with the dialysis machine.

1.2.2

Responsibility and disclaimer

The manufacturer accepts responsibility for the safety, reliability, and performance of
this equipment only if the following conditions are fulfilled:

●

Installation, operational procedures, maintenance, calibrations and repairs are
carried out by appropriately trained and suitable qualified people.

●

All equipment modifications are authorised in writing by the manufacturer and
carried out by appropriately trained and suitable qualified people.

●

The electrical installation of the relevant room complies with all applicable local
electrical codes and, if applicable, IEC requirements.

●

The equipment is used in accordance with the published operator’s manual.

Baxter does not accept any responsibility or liability for use of accessories or
disposables other than those specified in this manual or if any specified accessory or
disposable is not used in accordance with this manual, online instructions and the
instructions for use accompanying those accessories and disposables.

The patient’s physician is responsible for counselling, home care follow-up and
medical maintenance that comes with the treatment. Baxter has no responsibility for
any of these activities.

«
...
17
18
19
20
21
...
»

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands