manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 134

A:132

AK 98 Dialysis Machine - Measuring blood pressure

HCEN12745 Revision 10.2016

Program version 2.xx

An alarm will occur if a value is outside the set alarm limits.

Procedure

1)

Press the

BPM

button.

2)

Select the

Alarm

tab.

3)

Press

Set limits

.

4)

Select the alarm limits you want to set.
Enter the alarm limit value.

5)

Press

OK

.

6)

Repeat step 4 and 5 for all of the alarm
limits you want to set. Close the

Set

Limits

menu.

7)

Press the activate button for alarm limits to
activate the new settings.

8.7

Patient care during blood pressure measuring

8.7.1

All patients

CAUTION!

Check the material used in cuff before use to avoid allergic symptoms. Allergic
symptoms caused by the fabric material of the cuff could lead to exanthema and
urticaria with swollen skin and intense itching in the cuff area.

CAUTION!

Check the material used in cuff before use to avoid allergic symptoms. Multiple or
few petechia (small purple spots containing blood) on the forearm following the
application of the cuff which may lead to decrease of thrombocytes in the blood.
Inflammation of a vein (phlebitis) may be observed.

CAUTION!

Continuous cuff pressure due to kinks in the connection tubing may result in blood
flow interference and cause harmful injury to the patient.

CAUTION!

Too frequent blood pressure measurements may cause injury to the patient due to
blood flow interference.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands