Gambro AK 98 Operator'S Manual Download Page 143

Page: 143 / 386

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - DIASCAN

A:141

The factors below affect the measuring.

Double or single needle treatment

: The measuring results are more reliable in

double needle treatments.

Profiling

: The clearance measurement can be affected if profiling of sodium and

bicarbonate is active.

Ultrafiltration (UF)

: It is not possible to measure clearance when isolated ultrafiltration

or ultrafiltration in steps or intervals is active.

Handling that affect the clearance measurement:

●

Changing the blood flow rate

●

Pressing the

Blood pump

button

●

Pressing the

Ultrafiltration

button

●

Pressing the

Fluid bypass

button

●

Changing the sodium or bicarbonate values in the dialysis fluid

●

Changing the temperature of the dialysis fluid

●

Changing the flow rate of the dialysis fluid

●

Changing the UF volume

●

Changing the linear UF profiling settings

●

Activating or deactivating linear UF profiling

●

Activating or deactivating sodium or bicarbonate profiling

●

Activating isolated UF

●

An alarm sending dialysis fluid to bypass the dialyzer

●

An alarm stopping the blood pump

Summary of Contents for AK 98



































































































































































































































































































































































































Search results

Summary of Contents for AK 98

Reviews:

Brands by name

Popular brands

Gambro AK 98, Operator'S Manual

Search results

Summary of Contents for AK 98

Reviews:

Brands by name

Popular brands