manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

The Gambro AK 98 Operator's Manual is available for free download from our website. This comprehensive manual provides essential instructions and guidance for operating the Gambro AK 98. Gain a deeper understanding of this product's features and functionality by accessing the manual at manualshive.com.

Share
Download
background image

A:82

AK 98 Dialysis Machine - Haemodialysis - Double needle

treatment

HCEN12745 Revision 10.2016

Program version 2.xx

4)

Hold the segment in place and close the
blood pump door.

5)

Press lightly on the blood line to place it in
the upper guide.

6)

Remove protective caps and attach the
end of the arterial blood line firmly to the
dialyzer; press and turn simultaneously.

WARNING!

Check that the arterial blood
line is firmly attached to the
dialyzer to prevent patient
blood loss.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Related manuals for AK 98

Bartscher 700 Series Instructions For Installation, Use And Maintenance Manual preview
700 Series
Brand: Bartscher Pages: 22
Landoll 7812 Operator And Parts Manual preview
7812
Brand: Landoll Pages: 52
Gason 7390 Operator'S Manual preview
7390
Brand: Gason Pages: 110
K&K M8700 Manual preview
M8700
Brand: K&K Pages: 8
Parr Instrument 4560 Operating Instructions Manual preview
4560
Brand: Parr Instrument Pages: 24
JBL 7130 Installation And Service Manual preview
7130
Brand: JBL Pages: 15
Keithley 7071 Instruction Manual preview
7071
Brand: Keithley Pages: 79
Kayakpro SUP ERGO Assembly Instruction Manual preview
SUP ERGO
Brand: Kayakpro Pages: 17
Yoshitake DS-1 Operation Manual preview
DS-1
Brand: Yoshitake Pages: 11
Nektar Panorama P1 User Manual preview
Panorama P1
Brand: Nektar Pages: 12
Ocean Sonics icListen User Manual preview
icListen
Brand: Ocean Sonics Pages: 45
Quanser QNET Physics and Dynamics Quick Start Manual preview
QNET Physics and Dynamics
Brand: Quanser Pages: 4
U-Line H-5334 Quick Start Manual preview
H-5334
Brand: U-Line Pages: 9
U-Line Green Machine H-3518 Instructions preview
Green Machine H-3518
Brand: U-Line Pages: 3
V.ORLANDI RP10 Installation, Operating And Maintenance Instructions preview
RP10
Brand: V.ORLANDI Pages: 144
SprotDog Pro hunter 2525 Operating Manual preview
Pro hunter 2525
Brand: SprotDog Pages: 28
Falcon CHIEFTAIN E1006 User Instructions preview
CHIEFTAIN E1006
Brand: Falcon Pages: 5
Griven AL2320 Instruction Manual preview
AL2320
Brand: Griven Pages: 36

Brands by name

Popular brands

Load more brands