manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

The Gambro AK 98 Operator's Manual is available for free download from our website. This comprehensive manual provides essential instructions and guidance for operating the Gambro AK 98. Gain a deeper understanding of this product's features and functionality by accessing the manual at manualshive.com.

Share
Download
background image

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Haemodialysis - Single needle treatment

A:107

5)

Attach the venous blood line. Follow the
steps in Section 4.2.5

“Attach the venous

blood line”

on page A:84, but do not

attach the end of the venous blood line to
the dialyzer.

6)

Attach the venous expansion chamber.

Place the venous expansion chamber
upright in the holder. Make sure that the
expansion chamber clicks into its correct
position.

The edge inside the holder should fit into
the groove of the expansion chamber.

7)

Connect the end of the venous blood line
to the expansion chamber blood line.

8)

Connect the other blood line from the
expansion chamber to the dialyzer.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Related manuals for AK 98

T-Drill F-400 Instruction Manual preview
F-400
Brand: T-Drill Pages: 75
Zeiss KS Instructions For Use Manual preview
KS
Brand: Zeiss Pages: 38
National Instruments 9403 Getting Started Manual preview
9403
Brand: National Instruments Pages: 16
Jasco PRO Series Setup preview
PRO Series
Brand: Jasco Pages: 11
Unex UD-211-002-200 Operating Manual preview
UD-211-002-200
Brand: Unex Pages: 5
ACCO Brands LOUDEN 200 Series Installation, Operation, Maintenance And Parts Manual preview
LOUDEN 200 Series
Brand: ACCO Brands Pages: 144
B&K 4416 Service Manual preview
4416
Brand: B&K Pages: 16
B&G H5000 Pilot Quick Reference Manual preview
H5000 Pilot
Brand: B&G Pages: 2
Califone WT1 User Manual preview
WT1
Brand: Califone Pages: 7
CALITEK Grizzly 600 Manual preview
Grizzly 600
Brand: CALITEK Pages: 16
LAHTI PRO 46033 User Manual preview
46033
Brand: LAHTI PRO Pages: 20
LAHTI PRO 46017 User Manual preview
46017
Brand: LAHTI PRO Pages: 16
J&M 32 Series Operator'S Manual preview
32 Series
Brand: J&M Pages: 53
Qazqa 46060 Instruction Manual preview
46060
Brand: Qazqa Pages: 2
Eaton PowerXL DX-NET-ETHERNET2-2 User Manual preview
PowerXL DX-NET-ETHERNET2-2
Brand: Eaton Pages: 48
Eaton Power Xpert C445 Manual preview
Power Xpert C445
Brand: Eaton Pages: 2
Madsen zodiac Reference Manual preview
zodiac
Brand: Madsen Pages: 206
Vatech Smart Plus PHT-35LHS Technical Manual preview
Smart Plus PHT-35LHS
Brand: Vatech Pages: 190

Brands by name

Popular brands

Load more brands