manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

The Gambro AK 98 Operator's Manual is available for free download from our website. This comprehensive manual provides essential instructions and guidance for operating the Gambro AK 98. Gain a deeper understanding of this product's features and functionality by accessing the manual at manualshive.com.

Share
Download
background image

A:84

AK 98 Dialysis Machine - Haemodialysis - Double needle

treatment

HCEN12745 Revision 10.2016

Program version 2.xx

10)

Connect the arterial blood line with the
saline or priming solution bag. Check that
the connections are tight.

11)

Attach the arterial pressure transducer
protector of the arterial blood line to the red
arterial pressure transducer connector.
Press to pierce the membrane and then
turn to secure the connection.

12)

Close all relevant clamps.

CAUTION!

Check that all relevant
clamps are closed to prevent
undetected blood loss.

4.2.5

Attach the venous blood line

The venous blood line has blue connectors.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Related manuals for AK 98

Rangevision PRO Setup And Calibration Instructions preview
PRO
Brand: Rangevision Pages: 31
Falcon 90 Instructions For Use And Installation preview
90
Brand: Falcon Pages: 52
Ecco 200 Series Installation & Operating Instructions preview
200 Series
Brand: Ecco Pages: 4
JD Squared 3 Assembly & Operating Instructions preview
3
Brand: JD Squared Pages: 15
DAPAudio D1256 Manual preview
D1256
Brand: DAPAudio Pages: 16
3M 400 Series User Instructions preview
400 Series
Brand: 3M Pages: 28
Ace AFM-5 Operating Manual preview
AFM-5
Brand: Ace Pages: 17
ACE INSTRUMENTS Solid Operating Manual preview
Solid
Brand: ACE INSTRUMENTS Pages: 33
ACE INSTRUMENTS ALP-1 med Quick Start Manual preview
ALP-1 med
Brand: ACE INSTRUMENTS Pages: 2
ACE INSTRUMENTS ACE Easy Quick Start Manual preview
ACE Easy
Brand: ACE INSTRUMENTS Pages: 2
TapFlo DT Series Original Instruction preview
DT Series
Brand: TapFlo Pages: 35
DANA DT Series Assembly Instructions Manual preview
DT Series
Brand: DANA Pages: 8
2E PSE801 User Manual preview
PSE801
Brand: 2E Pages: 6
RASHA PROFESSIONAL Orbit Quick User Manual preview
Orbit
Brand: RASHA PROFESSIONAL Pages: 11
MADRIX LUNA Technical Manual & Quick Start Manual preview
LUNA
Brand: MADRIX Pages: 24
MADRIX LUNA Quick Start Manual preview
LUNA
Brand: MADRIX Pages: 28
DB Industries DELTA 2 User Instructions preview
DELTA 2
Brand: DB Industries Pages: 60
vc999 K5 Operating Manual preview
K5
Brand: vc999 Pages: 55

Brands by name

Popular brands

Load more brands