Gambro AK 98 Operator'S Manual Download Page 232

Page: 232 / 386

B:32

AK 98 Dialysis Machine - Alarms

HCEN12745 Revision 10.2016

Program version 2.xx

115 Low arterial pressure

115 Low arterial pressure

Appears:

When the patient’s arterial pressure reaches the set low
alarm limit. The arterial pressure is the pressure in the
blood line from a patient.

Machine actions:

●

The blood pump stops.

●

The venous blood line clamp closes.

●

Ultrafiltration rate is set to zero.

Operator action:

Stop the blood pump. The arterial and venous pressure
alarm limits are automatically widened.

Check that the patient´s blood flow rate is the same as
the blood flow rate set in the dialysis machine.

Check the patient´s blood pressure.

Check the position of the arterial needle.

Check that there are no kinks or clots in the arterial
blood line between the needle and the point where the
blood pressure is measured.

Adjust the blood flow and restart the blood pump.

Check the arterial and venous pressures and press the
flashing pressure control to re-centralise the alarm
limits.

When the arterial pressure is within the set alarm limits
again, the blood pump starts automatically and the venous
blood line clamp opens.

Summary of Contents for AK 98



































































































































































































































































































































































































Search results

Summary of Contents for AK 98

Reviews:

Brands by name

Popular brands

Gambro AK 98, Operator'S Manual

Search results

Summary of Contents for AK 98

Reviews:

Brands by name

Popular brands