manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 257

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Alarms

B:57

214 Pv and Qd settings in conflict

214 Pv and Qd settings in conflict 

Increase Qd to 500 mL/min. 

Appears:

When the dialysis machine cannot achieve the set UF rate
since there is a conflict between the patient’s venous
pressure and the set dialysis fluid flow rate.

Machine actions:

The dialysis fluid bypasses the dialyzer.

Operator action:

1.

If possible, increase dialysis fluid flow rate to at least
500 ml/min:
- Press the

Fluid

button.

- Select the

Fluid flow

tab.

- Press

Dialysis fluid flow

and adjust the flow

rate.

2.

If you cannot increase the dialysis fluid flow rate,
decrease the venous pressure and wait, maximum 5
minutes, until the dialysis fluid enters the dialyzer again.

3.

If the alarm goes off again, consider ending the
treatment.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands