Fuji Electric Frenic lift, Reference Manual

Page: 30 / 254

2.1 Function Code Tables
2-17
Chap. 2
FUNCTION C
O
DES
 L codes: Lift Functions
Code Name Data setting range
Incr
em
ent
Un
it
Ch
a
n
ge
wh
en
runni
n
g
Da
ta
cop
yin
g
Default s
e
ttin
g
Data f
o
rm
a
t No.
To
rq
ue v
e
ctor
contr
o
l
Softw
ar
e ver
si
o
n
wh
ich
ca
n b
e
used
L01 Pulse Encoder (Selection)
- - N Y 0 1 -
A/B phase ABS signal
0
12/15 V (Complementary / Open collector),
5 V Line driver None
N
1 Z N
4 Sinusoidal differential voltage (1 V p-p) EnDat 2.1 (ECN1313 compatible) N
5 SIN/COS (ERN1387 compatible) N
6 BiSS-C (Sendix5873 compatible) N
7 SSI (ECN1313 compatible) N
8 Hiperface (SRS50 compatible) N
L02 (Resolution) 360 to 60000 1 P/R N Y 1024 1 N
*7
L03 Magnetic Pole Position Offset
(Tuning)
- - N N 0 21 N
0: Disable Y
1: Reserved for particular manufacturers N
3: Reserved for particular manufacturers N
4: Enable (motor stopped) N
5: Enable (motor rotated) N
Note: This setting is effective if F42 = 1.
1 to 4 : It is a recommended condition that the brake is a close.
5 :
It is necessary condition that the brake is a release and without load.
L04 (Offset angle) 0.00 to 360.00 (Return value of L03)
Note: This setting is effective if F42 = 1. 0.01 deg N Y 0.00 5 N
L05 ACR P constant - - - Y Y 1.5 3 N
L06 ACR I constant - - - Y Y 0.80 5 N
L07 Auto magnetic Pole Position tuning
mode select
- - N N 0 21 N
0: Disable Y
1: Enable N
3: Enable (with checking accuracy) N
4: Enable (for SPM) N
Note: This setting is effective if F42 = 1.
1 to 4 : It is a recommended condition that the brake is a close.
L09 Filter Time Constant for Reference
Speed (Final)
0.000 to 0.100 0.001 s Y Y 0.000 7 Y
L10 Filter Time Constant for Detected Speed 0.000 to 0.100 0.001 s Y Y 0.005 7 N
*7
L11 Multistep Speed Command Combination
Zero Speed
00000000
b
to 00000111
b
(0 to 7)
Note: If a binary value within the range from 00000000
b
to
00000111
b
is double-assigned, the inverter trips with alarm
Er6.
1 - N Y 0 1 Y
L12 Manual Speed (Middle) 1 - N Y 1 1 Y
L13 Maintenance Speed 1 - N Y 2 1 Y
L14 Creep Speed 1 - N Y 3 1 Y
L15 Manual Speed (Low) 1 - N Y 4 1 Y
L16 Low Speed 1 - N Y 5 1 Y
L17 Middle Speed 1 - N Y 6 1 Y
L18 High Speed 1 - N Y 7 1 Y
L19 S-curve Setting 1 0 to 50% of max. speed 1 % Y Y 20 1 Y
L20 2 1 % Y Y 20 1 Y
L21 3 1 % Y Y 20 1 Y
L22 4 1 % Y Y 20 1 Y
L23
5
1 % Y Y 20 1 Y
L24
6
1 % Y Y 20 1 Y
L25
7
1 % Y Y 20 1 Y
L26
8
1 % Y Y 20 1 Y
L27
9
1 % Y Y 20 1 Y
L28
10
1 % Y Y 20 1 Y
L29 Short Floor Operation (Holding time) OFF(32767): Disable
0.00 to 10.00 0.01 s N Y 0.00 5 Y
L30 (Allowable speed) 0.00 to 6000
*1
(Equivalent with 0.00 to 200.00 Hz) Variable *3 N Y 0.00 37 Y
L31 Elevator Parameter
(Speed)
1 to 4000 (Elevator speed at maximum speed of the motor) 1 mm/s N Y 1000 1 Y
L32 (Over speed level) 50 to 120 1 % N Y 120 1 N
L33 (Over speed timer) 0.000 to 0.500 0.001 s N Y 0.000 7 N
L34 (Moving distance
in creepless operation)
0.0 to 6553.5 0.1 mm N Y 0.0 3 Y
*1 The data setting range is variable. Refer to Section 2.2.
*3 The unit changes depending on the setting of C21.
*7 If the speed detection is effective, it operates.