Fuji Electric Frenic lift, Reference Manual

Page: 20 / 254

2.1 Function Code Tables
2-7
Chap. 2
FUNCTION C
O
DES
Code Name Data setting range
Incr
em
ent
Un
it
Ch
a
n
ge
wh
en
runni
n
g
Da
ta
cop
yin
g
Default s
e
ttin
g
Data f
o
rm
a
t No.
To
rq
ue v
e
ctor
contr
o
l
Softw
ar
e ver
si
o
n
wh
ich
ca
n b
e
used
E30 Speed Arrival (FAR)
(Hysteresis)
0.00 to 6000
*1
(Equivalent with 0.00 to 200.00 Hz)
Variable *3 Y Y 14.5
*2
37 Y
E31 Speed Detection (FDT)
(Detection level)
0.00 to 6000
*1
(Equivalent with 0.00 to 200.00 Hz)
Variable *3 Y Y 1450
*2
37 Y
E32
(Hysteresis)
0.00 to 900.0
*1
(Equivalent with 0.00 to 30.00 Hz)
Variable *3 Y Y 14.5
*2
37 Y
E34 Current Detection 1 (ID) When you set 1 to L98:bit0,
Refer to
E34 and E35 are effective over torque current alarm (0t).
default
(Level 1)
0.00: (Disable) Variable A Y Y1 Y2 table 24 Y
Current value of 1 to 200% of the inverter rated current
E35 (Time) 0.01 to 600.00
E36
Speed Detection 2 (FDT2)
(Detection level)
0.00 to 6000
*1
(Equivalent with 0.00 to 200.00 Hz)
Variable
*3
Y Y 1450
*2
37 Y
E37
Current Detection 2 (ID2)
Refer to
(Level 2)
0.00: (Disable) Variable A Y Y1 Y2 default 24
Y
Current value of 1 to 200% of the inverter rated current
table
E39
Recommended running
direction (RRD)
(Detection level) 0 to 100
1 % N Y 0 1 N
E43
LED Monitor
- - Y Y 0 1 -
0: Speed monitor (Select by E48)
-
3: Output current
Y
4: Output voltage
Y
8: Calculated torque
Y
9: Input power
Y
18: Reference torque
N
19: Torque bias balance adjustment (Offset) (BTBB)
N
20: Torque bias gain adjustment (BTBG)
N
E45 Reserved *4
-
- - Y Y 0 1 Y
E46 Reserved *4
-
- - Y Y 1 1 Y
E47 Reserved *4
-
- - Y Y 5 1 Y
E48 LED Monitor
- - Y Y 0 1 -
(Speed monitor item) 0: Reference speed (final)
Y
2: Reference speed (pre-ramp)
Y
3: Motor speed
Y
*5
5: Elevator speed
Y
*5
8: Elevator speed (mm/s)
Y *5
E52
Keypad(Menu display mode) 0: Function code data editing mode
1 - N Y 0 1 Y
1: Function code data check mode
2: Full-menu mode
E59 Terminal [C1] Type selection 0: Current input: 0 to 20 mA (C1 function)
1 - Y Y 1 1 Y
(C1/V2) 1: Voltage input: 0 to 10 V (V2 function)
E61 Analog Input for:
Selecting function code data assigns the corresponding
(Extension function selection)
function to terminals [12], [C1] and [V2] as listed below.
[12]
- - N Y 0 1 -
E62
[C1] - - N Y 0 1 -
E63
[V2] - - N Y 0 1 -
0: None
Y
1: Speed command (Not reversible operation with polarity)
Y
2: Speed command (Reversible operation with polarity) (Nothing for [C1])
Y
4: Torque bias command
N
E98 Command Assignment to:
Selecting function code data assigns the corresponding
[FWD]
function to terminals [FWD] and [REV] as same as E01. - - N Y 98 1 -
E99
Additional available settings against E01 are listed below. - - N Y 99 1 -
98: FWD Run forward
Y
99: REV Run reverse
Y
*1 The data setting range is variable. Refer to Section 2.2.
*2 The factory default setting varies depending on the shipping destination.
*3 The unit changes depending on the setting of C21.
*4 Reserved for particular manufacturers. Do not access this function code.
*5 It is indicated depending on reference speed (final).