manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide 

90 

  

NOTE

 

 

Before executing a Backup on a  backup module make sure the Write Protection switch is set 

to Unlocked. 

 

If the backup module and the TCP/IP interface module are both installed, B&R is automatically 
performed only on the backup module. 

 

The  TCP/IP  interface  module  can  execute  B&R  only  with  Network  up  and  running  (network 
cable connected). 

  

  

  

In the pictures above the Backup/Restore Dialog is shown: 

the 

Devices

 window lists all of the available devices in the current configuration, 

the 

Backup Contents

 window lists any previous device backups. 

  

To perform a 

Backup

: 

1.

 

Press the Backup button (you will be warned that all previous backups will be overwritten) 

2.

 

The Status window shows information as the backup procedure is being executed 

  

  

To perform a 

Restore

: 

1.

 

Press the Restore button (you will be warned that all scanner configurations will be overwritten) 

2.

 

The Status window shows information as the restore procedure is being executed 

  

  

The 

Restore

 function also provides easy and secure Single Device Replacement: 

1.

 

Remove the scanner to be replaced 

2.

 

Connect the new scanner (make sure the new scanner has been previously set to default) 

3.

 

Run the Restore procedure by pressing the Restore Button (see: Restore procedure) 

  

  

To 

Erase

 any previous Backup: 

1.

 

Press the Erase button 

2.

 

All backups are deleted 

  

  

  

  

The 

Status

 window shows the status of the backup procedure as it is being executed. 

  

  
The following is a list of possible error messages: 

Module not present

: backup module not mounted or not ready, or Search for TCNM-ACBB Backup Memory at Device 

Startup parameter disabled 

Unable to Read Backup State

: GeniusPlus is unable to get connected to the device 

Backup function not allowed

: when device is in SMART-TEACH Menu mode 

Failed! (Device not found)

: Master is unable to reach the addressed device 

Failed! (Module is write protected)

: backup module Write Protection switch is set to Locked 

  

  

  

  

 

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands