manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 41

Data Communication Settings 

39 

Code Identifier 

A Code Identifier string can be included in the output message. 

Possible selections are: 

Selections: 

Disable

 

no code identifier is included in the output message 

  

Standard AIM ID

  the AIM standard identifier is included in the output message 

  

Custom

 

activates  the  Custom Code ID  strings group  allowing  to  define  an  identifier  string  for 
each code symbology. The string will be included in the output message. 

  

 

 

Standard Parameters 

  

Header String 

Headers (up to 128 bytes) can be defined and transmitted as a block preceding the barcode(s). 

Selections:  characters from 

NUL 

(00H) to 

~

 (7EH). 

  

Code Position Tx 

If enabled, the code position information is included in the output message. The scan line is divided into 256 physical 

positions and therefore the code position value is transmitted in a fixed 3-digit decimal format separated by a Code 
Field Separator before the Code Identifier field. 

The code position is determined at the 

center

 of the label and is checked to be between the Min and Max parameters 

specified in the configuration. 

  

Code Direction Identifier Enable 

If enabled (checked), the relative Code Direction Identifier string is included in the output message. 

The  forward,  reverse  and  unknown  direction  strings,  which  indicate  the  scanning  direction  with  respect  to  the  code 

direction, can be defined. 

  

Forward Direction String 

A Forward Direction string indicates that the current code has been scanned in the forward direction (scanning from 

left to right). This string ("+" is the default value) can be customized by the user including up to 32 characters. 

Selections: 

characters from 

NUL 

(00H) to 

~

 (7EH). 

  

Reverse Direction String 

A Reverse Direction string indicates that the current code has been scanned in the reverse direction (scanning from 

right to left). The string ("-" is the default value) can be customized by the user including up to 32 characters. 

Selections: 

characters from 

NUL 

(00H) to 

~

 (7EH). 

  

Unknown Direction String 

An Unknown Direction string indicates that it is not possible to determine the scanning direction of a code. This occurs 

for the Pharmacode code which has no start/stop characters and for some code reconstruction reading conditions. 

The string ("?" is the default value) can be customized by the user including up to 32 characters. 

Selections: 

characters from 

NUL 

(00H) to 

~

 (7EH). 

  

Motor OFF 

If checked, it allows sending the Motor OFF string whenever the motor is set OFF. The motor OFF condition can occur 

either through the Scan Speed or Energy Saving parameters. 

  

Motor OFF String 

It defines  the  message  string  (up  to 128  bytes)  that  will be  sent  whenever  a  Motor  OFF  condition  exists.  When  the 

Motor OFF condition occurs this string is sent instead of the Global No Read Message. 

Selections: 

characters from 

NUL 

(00H) to 

~

 (7EH). 

  

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands