Banner TCNM-AD Series Parameter Manual Download Page 50

Page: 50 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

TCNM-ACBB5 Gateway

Type

It allows selecting the Host interface network type (Fieldbus and non-Fieldbus) for communication to/from the Host

network.

CAUTION

When any Host interface network type is selected, the Main Serial Interface is not available for

communication and must not be electrically connected in the TCNM-ACBB5 connection box.

NOTE

When using the Backup and Restore Module with a TCNM-ACBB connection box, the module Net

Type and Address Selection hardware switch settings are read at power-up and override the

software settings. For correct software configuration, make sure these switch settings are

compatible with your application.

Selections:

None

No Host interface network type is selected. The Main

Serial Interface is available for communication with the

Host.

Profibus

Enables the Fieldbus branch to allow the Profibus interface

parameters to be configured.

DeviceNet

Enables the Fieldbus branch to allow the DeviceNet

interface parameters to be configured.

Ethernet/IP
(Ethernet/IP -
TCP/IP)

Enables the combination Fieldbus and TCP/IP branches for

parameter configuration of either the Ethernet/IP interface

(Fieldbus), the Ethernet TCP/IP Services which allow up to

2 User Sockets to be configured - (non Fieldbus), or both.

IP Addressing in the Line Parameters branch determines

the method of address selection, either user defined

(Static Assignment), DHCP or Remote Assignment.

CC-Link

Enables the Fieldbus branch to allow the CC-Link interface

parameters to be configured.

CANopen

Enables the Fieldbus branch to allow the CANopen

interface parameters to be configured.

Profinet
(Profinet IO -

TCP/IP)

Enables the combination Fieldbus and TCP/IP branches for

parameter configuration of either the Profinet IO interface

(Fieldbus), the Profinet TCP/IP Services which allow up to

2 User Sockets to be configured - (non Fieldbus), or both.

IP Addressing in the Line Parameters branch determines

the method of address selection, either user defined

(Static Assignment), DHCP or Remote Assignment.

Modbus TCP
(Modbus TCP -
TCP/IP)

Enables the combination Fieldbus and TCP/IP branches for

parameter configuration of either the Modbus TCP

interface (Fieldbus), the Modbus TCP/IP Services which

allow up to 2 User Sockets to be configured - (non

Fieldbus), or both.

IP Addressing in the Line Parameters branch determines

the method of address selection, either user defined

(Static Assignment), DHCP or Remote Assignment.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands