Banner TCNM-AD Series Parameter Manual Download Page 15

Page: 15 / 92

Code Definition

activates the

Local No Read Strings

and the Local Multiple

Read Strings groups where setting respectively a Local No

Read String and a Local Multiple Read String for each

group label.

Do not use this option when working in single-label mode.

No Read String

It defines the string to be displayed in case of Global No Read Message. It is possible to select either an ASCII or HEX

value.

Multiple Read Message

This parameter is only available when the Code Combination is set to

Standard Multi Label

Logical Combination

When checked, this parameter allows the Multiple Read String to be sent if, during the reading phase, the scanner

reads more than the number of the expected barcodes set by the configuration parameters.

Multiple Read String

This parameter is only available when Multiple Read Message is enabled and the No Read Message selection is different

from Local No Read(s) String. It defines the string to be displayed in case of Multiple Read Message. It is possible to

select either the ASCII or HEX value. If

disabled

, the scanner transmits the first code read.

Associate Same Codes When Read By Different Scanners

This parameter is available only when the Code Combination parameter is set to

Code Collection

and the scanner

Topology Role is

Master

. If enabled, it allows transmitting all codes belonging to the same programmed Slot (same

symbology and content) but read by different scanners (including the Master) in a single instance.

Codes Different When Scan Gap Is Greater Than

This parameter is available only when the Code Combination parameter is set to

Code Collection

If the number of

scans performed between two consecutive codes read (by the Master or Stand Alone scanner) is greater than the

defined number, the codes will be considered as different.

The parameter set to 0 means the filter is disabled: when there is no scan gap all the consecutive codes read will be

considered as only one code.

Codes Different When Code Position Gap Is Greater Than

This parameter is available only when the Code Combination parameter is set to

Code Collection

. If the position gap

between two consecutive codes read (by the Master or Stand Alone scanner) on the same scan line is greater than the

defined gap number, the codes will be considered as different.

The parameter set to 0 means the filter is disabled: when there is no code position gap all the consecutive codes read

will be considered as only one code.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands