manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 56

TCNM-AD/EX/SP Family Software Configuration Parameter Guide 

54 

Process Active Timeout (ms) 

This  value  specifies  how  long  the  module  shall  stay  in  the  PROCESS_ACTIVE-state  after  receiving  a  Modbus  TCP 

request. The valid values are in the range from 

0

 to 

65535

 ms. The default value is 0 = timeout disabled. 

  

  

Connection Timeout (s) 

This setting specifies how long a Modbus TCP connection may be idle before it is closed by the module. 

The valid values are in the range from 

0

 to 

65535

 seconds, default = 60 seconds. 0 = timeout disabled. 

  

 

 

Digital I/O Conditioning 

  

  

NOTE 

If any of the following parameters are enabled, the DAD  or DPD Driver starts at Byte 1 (second byte) of the 

Input/Output Areas, and Byte 0 of the Input/Output Areas is reserved for Digital I/O Conditioning parameters. 

If  none  of  the  following  parameters  are  enabled,  the  DAD  or  DPD  Driver  starts  at  Byte  0  (first  byte)  of  the 

Input/Output Areas. 

For details about the DAD or DPD Driver, refer to the "DAD / DPD Driver" document on the CD-ROM. 

The  DAD  or  DPD  Drivers  are  NOT  available  for  the  Fieldbus  networks  managed  under  the  Ethernet  TCP/IP 

Services branch (Ethernet/IP or Modbus TCP) since these protocols do not use Exchange Areas. 

  

  

Digital Input Lines 

Input 1 Echo 

If checked, the scanner Input 1 status is echoed to the Fieldbus Master via bit 0 in Byte 0 (LSB) of the Input Area. 

  

For Ethernet/IP under the TCP/IP Services branch, the Input 1 status is echoed to the Fieldbus Master using Assembly 

Object Instances. 

  

Input 2 Echo 

If checked, the scanner Input 2 status is echoed to the Fieldbus Master via bit 1 in Byte 0 (LSB) of the Input Area. 

  

For Ethernet/IP under the TCP/IP Services branch, the Input 2 status is echoed to the Fieldbus Master using Assembly 

Object Instances. 

  

  

Phase Echo 

If checked, the scanner Reading Phase status is echoed to the Fieldbus Master via bit 7 in Byte 0 (LSB) of the Input 

Area. This parameter is only available if Start Input from Fieldbus is enabled. 

  

For Ethernet/IP under the TCP/IP Services branch, the scanner Reading Phase status is echoed to the Fieldbus Master 

using Assembly Object Instances. 

  

  

Digital Output Lines 

Output 1 

This parameter is read-only if the scanner Output 1 is set to Use Local. If the scanner Output 1 is set to Use External 

Fieldbus, then this parameter can be checked to allow the Fieldbus Master to drive the scanner Output 1 via bit 0 in 

Byte 0 (LSB) of the Output Area. 

  

For  Ethernet/IP  under  the  TCP/IP  Services  branch,  the  Fieldbus  Master  can  drive  Output  1  using  Assembly  Object 

Instances. 

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands