manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 35

Reading Parameters 

33 

Triggered 

If checked, it allows assigning a trigger through which the oscillating mirror can be activated to work in a second 

reading zone according to the defined parameters. 

  

Second Zone Trigger 

This parameters defines the number of the input or the phase working as trigger. 
Selections: 

Phase

 (available only when working in On Line operating mode)

 

  

Input 1 

  

Input 2 

  

Second Zone Trigger Level 

This parameter allows setting the active state of the trigger. When the selected state is active, the oscillating mirror 

starts working in the second reading zone according to the parameters set: 
Selections: 

Active Open 

  

Active Closed 

  

Second Zone Oscillating Mode 

This parameter defines the oscillating mode of the scanner mirror to be used in the second reading zone: 

Selections: 

Fixed

 

the oscillating mirror deflects the scan line at a fixed angle of deflection (-
15°). 

  

Continuous

  the  scan  line  is  deflected  according  to  the  Second  Zone  Amplitude  and 

Second Zone Frequency settings. 

  

Second Zone Amplitude (degrees) 

This parameter is available only when working in Continuous Second Zone Oscillating Mode. 

It defines the deflection range in degrees as a symmetrical oscillation with respect to the fixed angle (-15°). 

Selections:  a value from 

10°

 to 

40°

:    

  

Second Zone Frequency (Hz) 

This parameter is available only when working in Continuous Second Zone Oscillating Mode. 

It defines the oscillating frequency in Hertz: 

Selections:  a  value  from 

0.5

  to 

4.0

 

Hertz: 

  

  

NOTE

 

The maximum allowable frequency for an amplitude of 35° or more is 3 Hz. 

  

  

 

 

TCNM-SPLD-OM Oscillating Mirror 

  

  

NOTE

 

This parameter group is available only for 

TCNM-SP

 scanners (Oscillating Mirror models). 

  

  

Oscillating Mode 

This parameter defines the oscillating mode of the scanner mirror: 

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands