Banner TCNM-AD Series Parameter Manual Download Page 68

Page: 68 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

Motor Failure

For TCNM-AD/EX scanners, if checked, it allows sending an alarm whenever the motor speed is above or below the

internal threshold with respect to the programmed Scan Speed.

Laser Failure

For TCNM-AD/EX scanners, if checked, it allows sending an alarm whenever a laser failure has occurred.

Oscillating Mirror Failure

For TCNM-AD/EX scanners, if checked, it allows sending an alarm whenever the oscillating mirror has not been

recognized.

Oscillating Mirror Data Consistency Error

For TCNM-AD/EX scanners, if checked, it allows sending an alarm whenever a checksum error has occurred on the

oscillating mirror onboard settings.

Start/Stop Input Failure

This parameter is available only when working in On Line operating mode and when the On Line Options parameter is

set to On Line Input 2. If checked, it generates an error if one of the two inputs (Start Input/Stop Input) does not
work.

Presence Sensor Stuck Timeout

This parameter is available only when working in On Line operating mode and when the Conveyor Info is available. It

defines the time interval after which an error is generated if the status of the presence sensor does not change

(presence sensor remains open).

Selections:

Disable

1 sec

2 sec

5 sec

10 sec

30 sec

1 min

Focus Displacement

If checked, it allows sending an alarm whenever the actual focus position doesn't match the Locked Position saved in

the scanner configuration memory. This alarm is generated when the focus position has exceeded the allowable

tolerance.

DIGITIZER: Motor Failure

If checked, it allows sending an alarm whenever the motor speed is above or below the internal threshold with respect
to the programmed Scan Speed.

DIGITIZER: Motor Life End

If checked, it allows sending an alarm when the motor has surpassed its factory declared functional life.

DIGITIZER: Laser Failure

If checked, it allows sending an alarm whenever a laser failure has occurred.

DIGITIZER: Laser Life End

If checked, it allows sending an alarm when the laser has surpassed its factory declared functional life.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands