Banner TCNM-AD Series Parameter Manual Download Page 14

Page: 14 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

decoded code/Multiple Read Message string

NOTE

In case the Multiple Read Message is enabled and both codes of the third group are decoded, the

Multiple Read string will also be transmitted. If the Multiple Read Message is disabled, only the

first decoded code of the third group is transmitted.

- 4 -

Code label setting#1 = Code 93

Code label setting#2 = Interleaved 2/5

Code label setting#3= EAN-8

Code label setting#4= UPC-A

Logical Combination Rule = 1^2&3^4
Defines 2 groups, each of them expecting one of the defined code types. The first group may expect a Code 93 label or

an Interleaved 2/5 label. The second group may expect an EAN-8 label or a UPC-A label.

Decoded Code Symbology

Output Message

Label

Label #2

Label

Label #4

---

---

---

---

---

---

---

<Header><Code93><DPS>< First decoded code/Multiple Read Message

string><Terminator>

---

<Header><First decoded code/Multiple Read Message string><DPS><EAN

8 data><Terminator>

---

<Header>< Interleaved 2/5 data><DPS>< First decoded code/Multiple

Read Message string ><Terminator>

---

---

---

---

<Header><First decoded code/Multiple Read Message string><DPS><

First decoded code/Multiple Read Message string ><Terminator>

NOTE

In case the Multiple Read Message is enabled and both codes of either group are decoded, the

Multiple Read string will also be transmitted. If the Multiple Read Message is disabled, only the

first decoded code of the relative group is transmitted.

No Read Message

The No Read condition occurs whenever a code cannot be read or decoded.

Selections:

Disable

Read

Message

the No Read Message is not transmitted.

Global

Read

Message

the No Read String will be sent if the scanner is unable to
decode one or more barcodes in the reading phase.

Local

Read(s)

Message

this option is useful when one or more codes are not read

in the reading phase or when more codes than the

expected number set by the configuration parameters are

read.
If working in Standard Multi Label mode, this option
activates the Code Label Local No Read String and the

Code Label Local Multiple Read String parameters which

allow setting a Local No Read String and a Local Multiple

string for each defined code symbology.

If working in Logical Combination Rule mode, this option

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands