Banner TCNM-AD Series Parameter Manual Download Page 66

Page: 66 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

Display

Display Language

This parameter sets the language used for all messages on the display.

Selection:

English

(United

States)

French (France)

German (Germany)

Italian (Italy)

Japanese (Japan)

Network Status Monitor

For Master devices (SYNCHRONIZED or MULTIDATA), when checked, this parameter enables Network Status messages

on the Master display (for scanners with display), and on the TCNM-ACBB5 accessory display if present.

Toggle Network Status Monitor with Last Data Read

Allows the Network Status Message to be toggled with the Last Data Read message on the Master display (for

scanners with display), and on the TCNM-ACBB5 accessory display if present.

Contrast (Local Device)

This parameter sets the contrast of the reader display. It has no effect on the TCNM-ACBB5 display (if present).

Selection: value from

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands