Banner TCNM-AD Series Parameter Manual Download Page 86

Page: 86 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

For field descriptions see Decoded Code.

Each field can appear or not depending on the configuration and the result of the reading.

Note

When the Code Field Length Setting parameter is

Fixed

, the <NO READ STRING> and <CODE FIELD> are subject to

the editing rules specified by the parameters:

Code Field Length

Data Justification

Fill Character

Wrong Read

Only for Code Verifier (Single Label):

Format

When Wrong String Tx and Wrong Code Tx are enabled:

<HEADER><WRONG READ><TERMINATOR>

where:

<WRONG READ> = [<WRONG READ STRING><WRONG READ CODE><INFO FIELD>] if read but NOT

Verifier Code

Each field can appear or not depending on the configuration and the result of the reading.

Diagnostic Messages

When enabled, Diagnostic Messages can be sent as an output message for certain error conditions.

Format

When Internal Numeric Messages are enabled:

<HEADER><DIAGNOSTIC HEADER><INTERNAL NUMERIC MESSAGE><DIAGNOSTIC TERMINATOR>

<TERMINATOR>

where:

<INTERNAL NUMERIC MESSAGE> = xx<#>yyy<space>
xx=

is the address of the scanner: 00 = Master; all others = Slaves

yyy=

is the diagnostic error number as described in the diagnostic tables.

When User Defined Strings are enabled:

<HEADER><DIAGNOSTIC HEADER>

<#>

<DIAGNOSTIC ERROR MESSAGE><DIAGNOSTIC TERMINATOR>

<TERMINATOR>

Each field can appear or not depending on the configuration and the result of the reading.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands