manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 45

Data Communication Settings 

43 

Network Diagnostics 

If checked it enables the Network Diagnostics Field in the Heartbeat message. The Network Diagnostics field is a fixed 

32-byte  field  (one  for  each  scanner  in  the  network  from  scanner  0  (Master),  to  scanner  31).  Each  byte  has  the 

following meaning: 

 

0 = Scanner not expected 

1 = Scanner OK 

2 = Scanner expected but not present (not connected or possible network failure) 

3 = Scanner Failure 

 

Heartbeat Terminator String 

This parameter signals the end of the Heartbeat message. It can be a string of up to 128 characters. 
Selections:  characters from 

NUL

 (00H) to 

~

 (7EH) 

 

The Heartbeat Header String should be different from the Heartbeat Terminator String. 

 
 

 

Main Serial Port Parameters 

  

Main Port Communication Mode 

The following communication modes can be selected when using the main serial port. 

Selections: 

Standard 

  

MUX 32 slave 

  

Siemens 3694 

  

Siemens RK512 

  

Standard

 

Standard  is  the  normal  mode  for  the  Main  Serial  Interface.  In  this  communication  mode  the  following  physical 

connections are allowed: 

 

RS232 

 

RS485 full-duplex 

Selecting Standard, the scanner will send out the data using the specified Handshake, but without any special protocol. 

  

MUX32 Slave

 

MUX32 slave is the communication mode used for connections to a Multiplexer. For such a configuration the scanner 

must be set with the same communication parameters (Baud rate, Parity, etc.) as the multiplexer. 

In this communication mode, only the RS485 half-duplex physical connection is possible. 

The following values are automatically set: 

 

No parity 

 

8 data bits 

 

1 stop bit 

  

3964

 

This communication mode is typically used for connections to a PLC. The following physical connections are allowed: 

 

RS232 

 

RS485 full-duplex 

  

  

RK512

 

For RK512 protocol the following parameters must be set: 

Checksum 

Filler Character 

Header Bytes 

Priority 

Filler Position 

  

  

Main Port Electrical Interface 

The Main serial interface is compatible with the following electrical standards: 

Selections: 

RS232

 

RS485

 full duplex 

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands