manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 29

Operating Modes 

27 

Enable 

When checked it enables the Code Verifier operating mode. 

  

Verifier Code 

The string used as the match code to the decoded codes. 

Selections: characters from 

NUL

 (00H) to 

~

 (7EH) 

  

Store Input 

It defines the number of the input used to automatically store the verifier code. This input must be activated before 

the reading phase starts, the verifier code must be read and then after the end of the reading phase the input must be 

deactivated. 

Selections:  from 

1

 to 

2

 

  

Active Level 

Allows the selection of the active state of the input. 

Selections: 

Active Closed

  the input is active when current flows through IN pins. 

  

Active Open

 

the input is active when there is no current flowing through IN pins. 

  

Right Code Tx 

When checked it enables the transmission of the Right Code. 

  

Wrong Code Tx 

When checked it enables the transmission of the Wrong Code. 

  

Wrong String Tx 

When checked it enables transmission of the Wrong String message. 

  

Wrong String 

The string sent in case of a mismatch (wrong code read). 

Selections: characters from 

NUL

 (00H) to 

~

 (7EH) 

  

  

  

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands