manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 6

TCNM-AD/EX/SP Family Software Configuration Parameter Guide 

4 

 

  

  

Operating Modes 

  

The wizard offers the following Operating modes: 

  

On Line Operating Mode 

This  operating  mode  causes  the  reader  to  be  connected  to  an  external  Presence  Sensor  using  EXT  TRIG+  and  EXT 

TRIG- inputs. 

During the active phase of the presence sensor, the scanners try to acquire and correctly decode the code. 

In case the decoding phase is successful, the barcode characters are transmitted on the serial interface. Otherwise, a 

no read message is sent. 

 

  

Automatic Operating Mode 

This operating mode does not require the connection to an external Presence Sensor. 

When  working  in  this  mode  the  reader  is  continuously  scanning,  while  the  reading  phase  is  activated  each  time  a 

barcode enters the reader reading zone. The reader stops reading after an N number of scans without a code. 

Barcode characters are transmitted on the serial interface. In case of a failed reading phase no message is sent to the 

host computer. 

 

  

Test Operating Mode 

This  operating  mode  causes  the  reader  to  be  continuously  activated  allowing  to  verify  its  reading  features  and  its 

reading position with respect to the barcode. For this reason, it is particularly advised during the installation phase of 

the reader. 

After 100 scans, the values relative to an internal counter and the decoded code are displayed and transmitted on the 

serial interface. The counter reports the percentage of good reads of the label. 

  

NOTE 

This operating mode is not used for SYNCHRONIZED network configurations. 

  

  

 

  

The following Operating Mode is not included in the Wizard but can be selected from the Operating Mode parameters: 

 

Continuous Operating Mode 

The reading phase is always active and, differently from the Automatic operating mode, it also allows reading two or 

more codes when placed along the same scan line. 

Code transmission is identical to the other operating modes except that there is no transmission on the serial port in 

case of a No Read condition. 

  

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands