Banner TCNM-AD Series Parameter Manual Download Page 73

Page: 73 / 92

Diagnostics

User Defined Message Examples

Stand Alone

Motor Failure (default string)

<STX>#Motor Failure<ETX>

"Motor Failure" (user defined string)

Master

Master (00) digitizer motor failure (default string) +

Slave 01 not responding (default string)

<STX>00#Motor Failure 01#Slave

Not Responding<ETX>

"Motor Failure" + "Slave Not Responding" (user defined

strings)

Local Network Failure

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever the local ID-NET™

network controller failure is present.

Motor Failure

For TCNM-AD/EX scanners, it defines the message string (up to 128 bytes) that will be sent as a diagnostic message

whenever the motor speed is above or below the internal threshold with respect to the programmed Scan Speed.

Laser Failure

For TCNM-AD/EX scanners, it defines the message string (up to 128 bytes) that will be sent as a diagnostic message

whenever a laser failure has occurred.

Oscillating Mirror Failure

For TCNM-AD/EX scanners, it defines the message string (up to 128 bytes) that will be sent as a diagnostic message

whenever the oscillating mirror has not been recognized.

Oscillating Mirror Data Consistency Error

For TCNM-AD/EX scanners, it defines the message string (up to 128 bytes) that will be sent as a diagnostic message

whenever a checksum error has occurred on the oscillating mirror onboard settings.

Start/Stop Input Failure

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever a start/stop input

failure is present.

Presence Sensor Stuck Timeout

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever a presence sensor

stuck timeout is present.

No Phase Warning

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever the No Phase

Timeout expires (no phase activity - on or off).

Focus Displacement

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever the actual focus

position doesn't match the Locked Position saved in the scanner configuration memory. This alarm is generated when

the focus position has exceeded the allowable tolerance.

DIGITIZER: Motor Failure

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever the motor speed is

above or below the internal threshold with respect to the programmed Scan Speed.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands