Banner TCNM-AD Series Parameter Manual Download Page 76

Page: 76 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

Fieldbus Failure

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever there is a

communication error between the scanner and the Fieldbus module inside the TCNM-ACBB5 connection box.

Fieldbus DHCP Problem

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever there is a

communication problem between the DHCP server and the Fieldbus module inside the TCNM-ACBB5 connection box.

Fieldbus Configuration Error

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever a configuration

error has occurred between the scanner and the Fieldbus module inside the TCNM-ACBB5 connection box.

Fieldbus Mismatch

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever the Fieldbus

module inside the TCNM-ACBB5 doesn't match the one saved in the scanner configuration memory.

Wrong TCNM-ACBB Backup Module Rotary Switch Selection

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever one or more of the
selected Backup module Rotary Switch settings inside the TCNM-ACBB doesn't match the scanner configuration

memory.

TCNM-ACBB Backup Module Communication Failure

It defines the message string (up to 128 bytes) that will be sent as a diagnostic message whenever there is a

communication error between the scanner and the Backup module inside the TCNM-ACBB connection box.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands