Banner TCNM-AD Series Parameter Manual Download Page 51

Page: 51 / 92

Data Communication Settings

Ethernet
TCP/IP
Ethernet/IP
(explicit

messaging)
Modbus TCP

Enables the combination TCP/IP services (up to 2 User

Sockets can be configured) and/or the following fieldbus:

Ethernet/IP (Explicit Messaging), Modbus TCP (Server or

Client).

IP Addressing in the Line Parameters branch determines

the method of address selection, either user defined

(Static Assignment) or DHCP.

NOTE

GeniusPlus can be connected for scanner configuration directly through the Ethernet TCP/IP

connection. See Configuration Through Ethernet.

Line Parameters

The parameters available in this group define and report the fundamental information about the system.

For details refer to "Internetworking with TCP/IP, vol. I", by Douglas E. Comer.

MAC

This is a read-only parameter, which displays the address of the network interface card (NIC).

Baud Rate

This is a read-only parameter. All modules are set to use the automatic baud rate mechanism where the Fieldbus-

TCP/IP Master defines the speed of the connection. After connection the actual speed will be displayed in this

parameter.

IP Addressing

Selections:

Static Assignment

the IP Address can be set manually through the IP_address,
IP_netmask and IP_gateway parameters.

DHCP

the IP address is assigned by a DHCP server when getting the
scanner configuration. In this case the IP address parameters

are read-only and display the DHCP assigned address.

Remote Assignment

the IP address is assigned by a remote network device (PC)
using the IPConfig address configuration application available

on the CD-ROM. In this case the IP address parameters are

read-only and display the remotely assigned address.

IP_address

If the IP Addressing parameter is set to Static Assignment, the Internet Protocol (IP) network address can be defined

manually. Consult your network administrator to obtain a new address. For other IP Addressing selections, this

parameter is read-only.

IP_netmask

If the IP Addressing parameter is set to Static Assignment, the subnet mask address can be defined manually. Consult

your network administrator to obtain a new address. For other IP Addressing selections, this parameter is read-only.

IP_gateway

If the IP Addressing parameter is set to Static Assignment, the gateway address can be defined manually. Consult

your network administrator to obtain a new address. For other IP Addressing selections, this parameter is read-only.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands