manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 18

TCNM-AD/EX/SP Family Software Configuration Parameter Guide 

16 

Code Label Settings 

  

  

The parameters available in this group define the properties of the code symbology selected. 

  

Enable 

Checking this box allows setting all parameters defining the code to be read. 

  

Code Symbology 

You can select the code type to be read in a wide range of symbologies. 
The following is the complete list of all the code types that are available: 

CODE 128 

GS1-128  (ex  EAN 

128) 

All EAN-UPC 

PLESSEY 

ISBT 128 

EAN 13 

CODABAR 

GS1 DataBar 

INTERLEAVED 2 OF 5  EAN-8 

ABC CODABAR 

GS1 DataBar Limited 

CODE 39 

UPC-A 

CODE 93 

GS1 DataBar Expanded 

CODE 39 FULL ASCII 

UPC-E 

PHARMACODE 

  

  

EAN Add On 

This parameter is available only for EAN/UPC code symbologies. It allows defining the Add On: 

Selections: 

No Add On

 

the selected EAN/UPC code has no additional digit; 

  

2 digits Add On

  the selected EAN/UPC code has 2 additional digits; 

  

5 digits Add On

  the selected EAN/UPC code has 5 additional digits; 

  

Label Length 

The label length (in number of characters/digits) can be specified in order to be accepted for decoding. 

Selections: 

Variable

 

all  possible  label  lengths  (in  number  of  characters/digits)  allowed  for  the  code 

selected are accepted. 

  

Fixed

 from 

1

 to 

60

 

only the selected length is accepted. 

  

Fixed

 from 

2

 to 

74

 

for 

GS1 DataBar Expanded

 only the selected length is accepted. 

  

The selection of a fixed label length is advised whenever possible. 

  

  

NOTE

 

This  parameter  is  not  available  for  the  following  code  symbologies,  since  their  label  length  is  automatically 

defined: 

- EAN-8 

- UPC-E 

- EAN-13 

- All EAN-UPC 

- UPC-A 

  

  

Check Digit 

The check digit control can be enabled to improve decoding safety: it is generally the last digit aligned to the right of 

the code and verifies the validity of the preceding digits. The calculation technique and number of check digits depend 

on the code selected. 

It is advised to enable the check digit whenever correct code identification is difficult. 

The following barcode symbologies include check digits in their definitions: 
- Code 128 
- EAN/UPC 
- Code 93 

For these symbologies the check digit control is not allowed. 

  

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands