manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 55

Data Communication Settings 

53 

Node Address (MAC ID) 

  

NOTE

 

When using the Backup and Restore Module with a TCNM-ACBB5 connection box, the module Net 

Type and Address Selection hardware switch settings are read at power-up and override the 

software settings. For correct software configuration, make sure these switch settings are 

compatible with your application. 

  

  

The Media Access Control Identifier (MAC ID) is an integer identification value assigned to each node of the Fieldbus 

network. The defined value distinguishes a node from all other nodes on the same link. 

Selections: 

  

  

  

(1)

 Profibus  a value in the range 

0 - 126

 

  

(2)

 

DeviceNet 

a value in the range 

0 - 64

 

  

(3)

 CC-Link  a value in the range 

1 - 64

 

  

(4)

 CANopen  a value in the range 

1 - 128

 

  

(1)

 For Profibus, the Node Address 126 forces the SSA (Set Station Address) service which allows the Fieldbus Master to 

assign  the  slave  node  address.  It  is  no  longer  possible  to  visualize  the  new  address  from  the  slave  node  after  the 

Master sets it. 

  

(2)

 For DeviceNet, the Node Address 64 allows the Fieldbus Master to assign the slave node address. It is possible to 

visualize the new address from the slave node after the Master sets it. 

  

(3)

 The range of valid addresses for CC-Link depends on the assigned Input/Output Area Size as follows: 

If the Input Area is greater than 6 or the Output Area is greater than 8, the max Node Address is 63. 

If the Input Area is greater than 14 or the Output Area is greater than 16, the max Node Address is 62. 

If the Input Area is greater than 22 or the Output Area is greater than 24, the max Node Address is 61. 

  

(4)

  For  CANopen,  the  Node  Address  128  forces  the  LSS  (Layer  Setting  Service)  which  allows  the  Fieldbus  Master  to 

assign the baud rate and address, but it is no longer possible to visualize the new address value from the slave node. 

  

Data Flow Control 

It  implements  a  reliable  transmission  protocol  between  Fieldbus  Master  (PLC)  and  Slave  (Fieldbus  module)  allowing 

specific functionalities such as Synchronization, Fragmentation/Reassembling  and Data Consistency. For more details 

refer to the "DAD / DPD Driver" document on the CD-ROM. 

Selections: 

Disable 

  

DAD Driver 

  

DPD Driver 

  

Data Consistency 

If checked (enabled), it allows improving the overall communication robustness of the Fieldbus network. For more 

details refer to the "DAD / DPD Driver" document on the CD-ROM. 

  

Version 

This parameter appears only if the Fieldbus type is CC-Link. It indicates the software version of the CC-Link controller. 

The possible values are Version 

1

 or 

2

. 

  

Stations 

This is a read-only parameter that appears only if the Fieldbus type is CC-Link. It indicates how many logical stations 

are assigned to the physical slave. 

  

Cycles 

This is a read-only parameter that appears only if the Fieldbus type is CC-Link. It indicates the number of cycles the 

CC-Link Fieldbus Master must perform on the logical stations in order to manage the Exchange Areas. 

  

  

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands