Banner TCNM-AD Series Parameter Manual Download Page 57

Page: 57 / 92

Data Communication Settings

Output 2

This parameter is read-only if the scanner Output 2 is set to Use Local. If the scanner Output 2 is set to Use External

Fieldbus, then this parameter can be checked to allow the Fieldbus Master to drive the scanner Output 2 via bit 1 in

Byte 0 (LSB) of the Output Area.

For Ethernet/IP under the TCP/IP Services branch, the Fieldbus Master can drive Output 2 using Assembly Object

Instances.

TCP/IP Services

UserSocket #n

The TCP/IP protocol provides two (user-defined) application sockets for communication. For further details refer to the
following bibliography:

Internetworking with TCP/IP, vol. I (chap. 20), by Douglas E. Comer

UNIX, network programming, by W. Richards Stevens

All the parameters managing the Heartbeat are available in the Heartbeat parameters group.

Status

Enables the TCP/IP User Socket #n.

Data Tx

If enabled (checked), data from the scanner will be transmitted on the TCP/IP User Socket.

Heartbeat

This parameter enables/disables transmission of the Heartbeat message used to signal device or system status at

regular intervals. The Heartbeat message is independent from Data Tx and can be enabled even if data is not sent on

the TCP/IP User Socket (Data Tx - disabled).
Selections:

Disable

the Heartbeat message is not transmitted

Enable Unconditioned

the Heartbeat message is always transmitted, even if

communication is still active

Enable Conditioned

the Heartbeat message is transmitted only when there is no

communication

Type

It defines the type of the socket:
Selection:

Server

For all TCP/IP Host Interface Modules, the station waits for connection and can
communicate with one single client at a time. If a second connection is opened by

the same peer machine with an application socket of type server TCP, this new

connection will replace the first.

Client

The station tries a connection towards the server.

Server_address

This parameter is available only when the socket is configured as a Client. It defines the IP address of the server to

which the client tries to connect.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands