manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 83

References 

81 

[132] 

Presence  Sensor  Warning

:  both  the  presence  sensors  remain  closed  for  more 

than the programmed No Phase timeout. This message may indicate that no pack is 

present  on  the  conveyor.  Furthermore,  it  is  assumed  that  both  presence  sensors 

are correctly synchronized otherwise a [131] or [133] error would be generated. 

[133] 

PS Output Failure

: the PS Input is active while the PS Output is inactive. When no 

information  about  movement  is  provided,  it  is  assumed  that  the  broken  presence 

sensor is the one which does not signal the packs entering the tracking area. The 

correct  synchronization  of  the  two  presence  sensors  is  periodically  checked  by 

counting the number of their status changes within a sampling period of 4 minutes. 

[149] 

Not available 

 

Serial On Line Mode 

 

Diagnostics

 

Error Number

 

Meaning

 

[132] 

Presence  Sensor  Warning

:  there  is  no  Reading  Phase  for  more  than  the 

programmed No Phase timeout. This message may indicate that no pack is present 

on the conveyor. 

 
 

Local Device Network Settings 

  

By selecting the "Local Device Network Settings" from the Device menu, the following dialog box appears allowing to 
define the topology role of the local scanner: 

  

  

 

  

  

SYNCHRONIZED:  The  Master  SYNCHRONIZED  /  Slave  SYNCHRONIZED  configuration  is  the  traditional  ID-NET™ 

network configuration in which the On-Line Operating Mode is used. 

  

MULTIDATA: 

The  Master  MULTIDATA  /  Slave  MULTIDATA  configuration  is  an  ID-NET™  network  configuration 
which allows the Slave scanners to be configured differently and independently from the Master. In 

this way the Slave scanners act as Stand Alone Devices which can send their data not only to their 
configured communication channels but also to the Master. The Master can be configured to send 

this  data  as  a  complete  message  to  its  configured  communication  channels  with  header,  address 

and separators (see Multidata). 

  

  

  

Topology Role

 

Defines the scanner topology role: 

Master SYNCHRONIZED: The  scanner  is  connected  as  an  ID-NET™  Master  in  a  master/slave  synchronized 

configuration. 

Slave SYNCHRONIZED:  The scanner is connected as an ID-NET™ Salve in a master/slave synchronized configuration. 
Master MULTIDATA: 

The scanner is connected as an ID-NET™ Master in a master/slave multidata configuration. 

Slave MULTIDATA: 

The scanner is connected as an ID-NET™ Salve in a master/slave multidata configuration. 

Other: 

This  selection  allows  Local  Device  Alternative  Network  Settings  to  support  (Master/Slave 

RS232 networks or Stand Alone applications. 

  

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands